Caterpillar D7E WH (Tier 4 Interim/Stage IIIB) Base
Ex-showroom Price
Price not available
Variants
Specifications of Caterpillar D7E WH (Tier 4 Interim/Stage IIIB) Base
Engine
- Bore 4.5 in
- Displacement 567.0 in3
- Engine Model Cat® C9.3 ACERT™
- Flywheel Power 235.0 hp
- Global Emissions U.S. EPA Tier 4 Interim/EU Stage IIIB/Japan MLIT Step 4
- Gross Power – ISO 14396 256.0 hp
- Gross Power – ISO 14396 (DIN) 260.0 hp
- Gross Power – SAE J1995 259.0 hp
- Net Power – ISO 9249 235.0 hp
- Net Power – ISO 9249 (DIN) 238.0 hp
- Net Power – SAE J1349 235.0 hp
- Stroke 5.9 in
Weights
- Operating Weight 68600.0 lb
- Operating Weight – LGP WHA 68600.0 lb
- Shipping Weight – LGP WHA 58900.0 lb
Service Refill Capacities
- Cooling System 22.5 gal
- Engine Crankcase 8.0 gal
- Final Drive (LGP each) 9.0 gal
- Fuel Tank 16.0 gal
- Pivot Shaft Compartment 1.8 gal
- Power Train 16.0 gal
Standards
- Brakes ISO 10265 2008
- Cab ANSI/SAE J1166 OCT 98
- ROPS/FOPS ROPS meets criteria ISO 3471:1994, 2008; FOPS meets ISO 3449:1992, 2005 Level II
Ripper
- Beam Cross Section 14.0 in
- Maximum Clearance Raised (under tip, pinned in bottom hole) 23.1 in
- Maximum Penetration 25.6 in
- Maximum Penetration Force 19639.0 lb
- Number of Pockets 3
- Overall Beam Width 82.2 in
- Pocket Spacing 35.4 in
- Pryout Force 52695.0 lb
- Ramp Angle 26.0 Degrees
- Shank Gauge 70.9 in
- Shank Section 72 mm × 228 mm (2.8 in × 9.0 in)
- Type Multi-Shank
- Weight – Each Additional Shank 330.0 lb
- Weight – With One Shank 3572.0 lb
Winch
- Drum Capacity – 24 mm (1 in) 203.0 ft
- Drum Capacity – 29 mm (1.13 in) 185.0 ft
- Drum diameter 12.5 in
- Increased Tractor Length – LGP 93.9 in
- Maximum Bare Drum – Line Speed 70.0 ft/min
- Maximum Bare Drum Line Pull 90000.0 lb
- Maximum Full Drum – Line Speed 116.0 ft/min
- Maximum Full Drum Line Pull 57000.0 lb
- Note *Basic winch weight, mounting arrangement, hydraulic and electrical system weight.
- Oil Capacity 3.2 gal
- Weight* 3350.0 lb
- Winch Drive Hydraulic
- Winch Model PA90
Hydraulic Controls - Pump
- Lift Cylinder Flow 42.0 gal/min
- Pump Output – Implement 52.8 gal/min
- Pump Output – Steering 82.4 gal/min
- Pump Type Piston, Variable Displacement
- Ripper Cylinder Flow 42.0 gal/min
- Tilt Cylinder Flow – Head End Flow 24.6 gal/min
- Tilt Cylinder Flow – Rod End Flow 17.4 gal/min
Hydraulic Controls - Main Relief Valve
- Bulldozer 4000.0 psi
- Ripper (Lift) 4000.0 psi
- Ripper (Pitch) 4000.0 psi
- Steering 5950.0 psi
- Tilt Cylinder 4000.0 psi
Drive Train
- AC Compressor Maximum Input Current 12.0 amps
- AC Compressor Nominal Input Voltage 320.0 volts
- AC Generator and Propulsion Module Voltage 480.0 volts
- Electric Water Pump System Nominal Input Current 5.0 amps
- Electric Water Pump System Nominal Input Voltage 320.0 volts
- Type Electric Drive
Bulldozer
- Blade 7S LGP
- Blade Capacity (SAE J1265)* 16.1 yd3
- Digging Depth 25.4 in
- Ground Clearance 49.8 in
- Height 4.4 ft
- Maximum Tilt 30.9 in
- Note *Capacities calculated with a trash rack installed.
- Weight** 8492.0 lb
- Width (over end bits) 14.91 ft
Select Equipment Dealers by Brand and City
Caterpillar D7E WH (Tier 4 Interim/Stage IIIB) Base Reviews
0.0
Overall
Based on 0 Reviews
Write Review