Caterpillar SH650 D Roof Support Carriers

Specifications of Caterpillar SH650 D Roof Support Carriers

Specifications

• Carry Capacity 45.0 tonnes
• Frame Oscillation 40.0 Degrees
• Gradients Possible (gradient data short-term only) 25°
• Ground Clearance 483.0 mm
• Maximum Speed with Load 19.3 km/h
• Motor/Engine Diesel
• Power Rated at 179.0 kW
• Pull Winch Rated at 34.0 tonnes
• Steering Control stick
• Steering Articulation 50.0 Degrees
• Torque/Tractive Effort 40256.0 kg
• Turn Radius (outside) 7.27 m
• Vehicle Length 11.68 m
• Vehicle Width 3.03 m
• Wheel Base 5.16 m

Brakes

• Hand Pump 1 Floor mounted hand pump located to the right of operator.
• Hand Pump 2 Activating this pump enables the operator to release the brake without power on the unit for towing a disabled vehicle.
• Service 1 Left foot-pedal actuated wet disc brakes at all four wheels.
• Service 2 Automatic Emergency/Park Brake Release.
• Service 3 A dash mounted monitoring gauge keeps the operator constantly informed of the accumulator’s status.
• Service 4 Accumulator is not permitted to fall below a certain residual pressure to assure this continued availability.
• Service 5 Demodulating/Failsafe parking and service brakes with cooling circuit.
• Service 6 Hydraulic power is supplied through a one gallon accumulator and is monitored by a charging/unloading valve.

Dimensions (Approximate)

• Cab Height with 508 mm (20 in) Cab (lower cab heights available on request) – With 48-in Tires 1727.0 mm
• Cab Height with 508 mm (20 in) Cab (lower cab heights available on request) – With 54-in Tires 1778.0 mm
• Chassis Height (nominal) – With 48-in Tires 1219.0 mm
• Chassis Height (nominal) – With 54-in Tires 1270.0 mm
• Empty Weights 45359.0 kg
• Frame Oscillation ±20°
• Ground Clearance: Nominal (please reference sales drawing for ground clearance profile) – With 48-in Tires 406.0 mm
• Ground Clearance: Nominal (please reference sales drawing for ground clearance profile) – With 54-in Tires 482.0 mm
• Inside turn radius 4140.0 mm
• Length Less Load Lifting and Battery Lift Forks 9601.0 mm
• Length with 2133 mm (84 in) Lifting Fork 11734.0 mm
• Length with Lift Plate Attachment 12192.0 mm
• Outside turn radius 7213.0 mm
• Overall Width – With Attachments and 48-in Tires 2997.0 mm
• Overall Width – With Attachments and 54-in Tires 3022.0 mm
• Steering articulation 100° Total
• Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 138 kW (185 hp) – Level and Empty on 0% Grade 13.7 km/h
• Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 138 kW (185 hp) – Level and Loaded on 0% Grade 6.7 km/ h
• Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 179 kW (240 hp) – Level and Empty on 0% Grade 16.3 km/h
• Tram Speed (calculated based on 4% rolling resistance): With Cummins C8.3 Engine 179 kW (240 hp) – Level and Loaded on 0% Grade 8.1 km/h
• Wheelbase 5155.0 mm

Drive Train

• Axles Front and rear rigid mounted outboard planetary axles with wet disc spring applied, hydraulically released brakes.
• Cooling System 1 Heavy Duty DST cooling system with 179 kW (240 hp) capability.
• Cooling System 2 Four and one-half fins per inch, 20.68 MPa (3,000 psi) pressure wash capable, brass tubed, cooling system.
• Drive Lines 7 and 8.5 Series shaft with 76.2 mm (3 in) slip joints.
• Power Component 1 DST Catalyst
• Power Component 2 Water Cooled Exhaust Manifold and Turbocharger
• Power Component 3 Charge Air Cooler
• Power Component 4 Intake System with Intake Flapper Valve Shutdown
• Power Component 5 DST Safety System
• Power Component 6 DST Flameproof Alternator
• Power Pack DST Air start package including: air starter, starter oil injector, water separator, pilot valve and operator control valves.
• Power Pack – Note Initial machine equipped with C8.3 138 kW (185 hp), but cooling & emissions control components sized for 179 kW (240 hp) engine
• Transmission 1 Six speed, power shift Clark 32000 transmission with 7C input and dual 8.5C outputs. Isolator mounted with dipstick fill.
• Transmission 2 External shell type, water to oil, shell cooler.

Hydraulics

• Bell-Crank Lift Cylinder Two (2) 203 mm (8 in) bore, double acting cylinders with load locking valves mounted on both the up and down functions.
• Hydraulic PTO Two (2) quick coupler connections, 17.58 MPa (2,550 psi) maximum recommended operating pressure.
• Pump Filtration 1 One 5 micron filter on the accumulator circuit
• Pump Filtration 2 One 5 micron filter on the main hydraulic circuit
• Pump Filtration 3 One remote mounted 5 micron return filter
• Pump Filtration 4 One 5 micron filter on the pilot valve circuit
• Pump Filtration 5 Standard – Three pressure filters
• Pump Motor Converter mounted, variable displacement, pressure compensated pump, 120.37 L/min (31.8 gal/min).
• Reservoir 1 Use Mobil Type 424 Hydraulic Oil
• Reservoir 2 Clean out plate to permit access to suction in-line strainer and cleaning and draining without removing from the machine
• Reservoir 3 An oil level sight gauge is located on the side of the tank and is easily visible.
• Reservoir 4 A 189 L (50 gal) capacity reservoir
• Reservoir 5 End mounted magnetic drain plug
• Reservoir 6 Spin-on filter/breather
• Reservoir Fill System System allows refilling of reservoir through the return line oil filter that is located in the top of the oil reservoir
• Steering Cylinder Two (2) 152 mm (6 in) bore, double acting cylinders with dual relief setting at 15.86 MPa (2,300 psi).
• Tilt Lift Cylinder Two (2) 241 mm (9 1/2 in) bore, double acting cylinders with load locking valves mounted on both the up and down functions.

FIRE SUPPRESSION

• Type 1 Also one 22.7 kg (20 lb) Class 10A60B: Hand held unit located in the operator's pit.
• Type 2 Automatic/Manual with linear detection wire.

LIGHTING SYSTEM

• Type 1 Four MSHA approved head lights
• Type 2 DST MSHA approved lighting package

OPERATOR’S COMPARTMENT

• Components 15 System Pressure Gauge
• Components 10 Warning Horn
• Components 11 RH Transmission Range Selection
• Components 12 LH Transmission Range Selection
• Components 13 Valve bank hydraulic functions: steering, bucket, bucket eject and winch/power take off
• Components 14 Park Brake Set/ Release
• Components 16 Accumulator Pressure Gauge
• Components 17 Park Brake Override
• Components 18 Side Egress Access

Lift and Carry Capacity

• Capacities Based on 54 × 26 Solid Tire at 1575 mm (at 62 in)
• Without Ballast 45. 0 tonnes

Dual Lift System

• Center Section 1 Entire center section area manufactured with T1 steel.
• Center Section 2 Center section is designed with hardened 102 mm (4 in) diameter pivot pins & spherical bearings to provide maximum load transfer
• Oscillation Section diameter
• Standard Load Lift Face Plate A combination bell-crank arm and bell-crank lifting cylinder for vertical lifting and tilting cylinders
• Standard Load Lift Face Plate Heavy duty forged alloy steel forks, 152 mm × 356 mm × 2134 mm (6 in × 14 in × 84 in)
• Tri-Section Frame 1 All high stressed areas are manufactured with T1 steel.
• Tri-Section Frame 2 Design produces a maximum of stability while maneuvering with a heavy load
• Tri-Section Frame 3 Design features multiple plate, modular construction for maximum strength and structural integrity
• Winch A fully hydraulic operated, 31 751 kg (70,000 lb) winch, with two speed pay in/out.
• Winch Cable Assembly 1 Equipped with a swaged-on thimble, connecting link and swivel hook
• Winch Cable Assembly 2 The standard winch cable is 25.4 mm (1 in) diameter, 6 × 37, IWRC, EIPS, class bright cable

Hydraulic Installation (Standard)

• Components JIC fittings with high pressure hosing; MSHA 2G flame resistant approved.

Cab Option

• Components Addition of 7th main control valve section and additional operator's control valve included.
• Fixed height 508 mm (20 in) Cab Assembly MSHA certified cab, formed support plate, access handles, completely enclosed grid and dual corner opening doors
• Hydraulically Adjustable 508 mm (20 in) Cab Assembly MSHA certified cab, formed support plate, access handles, completely enclosed grid and dual corner opening doors
• Manual Adjustable 508 mm (20 in) Cab Assembly MSHA certified cab, formed support plate, access handles, completely enclosed grid and dual corner opening doors
• Type Cab is manually adjustable.

Lift Attachments

• Fork Assembly 1 Designed to lift and carry 45 tonnes at 1575 mm (50 tons at 62 in) from the load lift plate mounted to the machine
• Fork Assembly 2 Set of 2134 mm (84 in) overall length up-set forged forks
• Quick Attach Lift Plate 1 Designed to lift and carry 45 tonnes at 1575 mm (50 tons at 62 in) from the face of the load lift frame
• Quick Attach Lift Plate 2 The plate mounts directly to forks through two parallel pockets and is held in place with two drop pins chained to lift plate
• Quick Attach Lift Plate 3 2134 mm (84 in) (Fork Assembly Required)