Caterpillar-SH650

Price not available

Caterpillar SH650 Roof Support Carriers

Variants

Specifications of Caterpillar SH650 Roof Support Carriers

Weights

  • Roof Support Carrier Empty Weights – Less Battery 31.7 kg
  • Roof Support Carrier Empty Weights – With 64-125-33, 200 amp Hour Battery 46.0 kg

Specifications

  • Carry Capacity 45.0 tonnes
  • Frame Oscillation 40.0 Degrees
  • Gradients Possible (gradient data short-term only) 25°
  • Ground Clearance 483.0 mm
  • Maximum Speed 6.2 km/h
  • Maximum Speed with Load 3.5 km/h
  • Motor/Engine DC/AC
  • Power Rated at 74.0 kW
  • Pull Winch Rated at 34.0 tonnes
  • Steering Control stick
  • Steering Articulation 50.0 Degrees
  • Torque/Tractive Effort 40256.0 kg
  • Turn Radius (outside) 7.27 m
  • Vehicle Length 11.68 m
  • Vehicle Width 3.03 m
  • Wheel Base 5.16 m

Brakes

  • Service and Emergency/Park 1 4-wheel wet disc
  • Service and Emergency/Park 2 Spring applied hydraulic release SAHR
  • Service and Emergency/Park 3 Controlled by reverse modulating valve
  • Service and Emergency/Park 4 Left pedal activated

Dimensions (Approximate)

  • Cab Height (Lower cab heights available on request) 1778.0 mm
  • Cab Height (Lower cab heights available on request) with 1219 mm (48 in) Tires Standard Cabs adjust from 1448 mm to 1702 mm (57 in to 67 in)
  • Cab Height (Lower cab heights available on request) with 1371 mm (54 in) Tires Standard Cabs adjust from 1524 mm to 1778 mm (60 in to 70 in)
  • Chassis Height (Nominal) with 1219 mm (48 in) Tires 1168.0 mm
  • Chassis Height (Nominal) with 1371 mm (54 in) Tires 1263.0 mm
  • Frame Oscillation – Total 40.0 Degrees
  • Ground Clearance (Nominal) – Please reference sales drawing for Ground Clearance profile: With 1219 mm (48 in) Tires 406.0 mm
  • Ground Clearance (Nominal) – Please reference sales drawing for Ground Clearance profile: With 1371 mm (54 in) Tires 471.0 mm
  • Inside turn radius 4140.0 mm
  • Length Less Load Lifting and Battery Lift Forks 7468.0 mm
  • Length of Fork 2042.0 mm
  • Length with 2134 mm (84 in) Lifting Fork 11679.0 mm
  • Length with Lift Plate Attachment 12039.0 mm
  • Outside turn radius 7214.0 mm
  • Overall Width with Attachments and 1219 mm (48 in) Tires 2819.0 mm
  • Overall Width with Attachments and 1371 mm (54 in) Tires 3021.0 mm
  • Steering Articulation – Total 100.0 Degrees
  • Wheelbase 5156.0 mm
  • Width 2855.0 mm
  • Width of Fork 356.0 mm

Drive Train

  • Axles Front/rear rigid mounted outboard planetary axles with wet disc spring applied, hydraulically released brakes.
  • Drive Lines 8.5 C Series shafts with 76.2 mm (3 in) slip joints
  • Motor Overspeed Protection Motor system is designed to prevent tram motor from overspeeding.
  • Tram Motor 1 Each 37.3 kW (50 hp) tram motor is coupled with a 5.77:1 ratio gearbox.
  • Tram Motor 2 Motors rated at 37.3 kW (50 hp) each for one hour (total of 74.6 kW [100 hp] per machine) at 1,500 rpm & 110V DC; foot mounted.
  • Tram Motor 3 Two mine traction, direct current, dual field, laminated frame gear motors.

Hydraulics

  • Battery Changer Cylinder Two (2) 152 mm (6 in) bore, double acting cylinders with load locking valves.
  • Bell-Crank Lift Cylinder Two (2) 203 mm (8 in) bore, double acting cylinders with load locking valves.
  • Filtration (Standard) 1 One tank mounted 25 micron return filter, and 10 micron fluid port filters on key control circuits.
  • Filtration (Standard) 2 10 micron on the pilot valve circuit
  • Filtration (Standard) 3 10 micron filter on the main hydraulic circuit
  • Filtration (Standard) 4 10 micron filter on the accumulator circuit
  • Filtration (Standard) 5 Three pressure filters
  • Hydraulic PTO Two (2) quick coupler connections, 175.8 bar (2,550 psi) maximum recommended operating pressure.
  • Pump The pump is a splined shaft fit to the pump motor.
  • Pump Motor 1 MSHA totally enclosed explosion proof; non-ventilated cooling.
  • Pump Motor 2 Mine duty, laminated frame, direct current motor rated at 11.93 kW (16 hp) for one hour; 110V DC.
  • Reservoir A 184.2 L (50 gal) capacity, integral reservoir.
  • Reservoir Fill System 1 System allows refilling of reservoir through the return line oil filter.
  • Reservoir Fill System 2 Venturi Jet refill system located on opposite side from operator on the middle frame.
  • Steering Cylinder Two (2) 127 mm (5 in) bore, double acting cylinders with dual relief setting at 159 bar (2,300 psi).
  • Tilt Lift Cylinder Two (2) 241 mm (91⁄2 in) bore, double acting cylinders with load locking valves.
  • Valve Banks Seven section, pilot operated, parallel type with internal relief and a dash mounted, glycerin filled pressure gauge.

FIRE SUPPRESSION

  • Type 1 9.1 kg (20 lb) hand held unit class 10A60BC
  • Type 2 Automatic/Manual with NPT Fittings, Eight Point, two on the front frame and six on the rear.

LIGHTING SYSTEM

  • Type 1 OCENCO, Halogen, 12V DC, 50 watt – two 12 volt quartz halogen.
  • Type 2 MCI, Halogen, 12V DC, 50 watt – two 12 volt quartz halogen front headlights and two rear headlights with protective guards.

OPERATOR’S COMPARTMENT

  • Components 1 Side Egress Access
  • Components 10 Circuit Breaker Reset
  • Components 11 Panic Strip Switch that de-energizes the Electrical system and applies the automatic brake
  • Components 12 Dash Mounted Glycerin Filled Hydraulic Gauges for accumulator, system pressure and emergency brake
  • Components 2 Warning Horn
  • Components 3 Right Hand Tilt-Lift Control Lever
  • Components 4 LH Hydraulic Winch (In-Out) Control Lever
  • Components 5 LH Hydraulic PTO Control Lever
  • Components 6 LH Battery Changer Control Lever
  • Components 7 Emergency/Park Brake Release
  • Components 8 Right Foot Accelerator Pedal
  • Components 9 Left Foot Brake Pedal Manuals
  • Left-hand steering with control stick with these functions • Pump motor start/stop • Park brake release/set • Directional headlights • Tram direction • Stop

Lift and Carry Capacity

  • Note Capacities based on 54 × 26 solid tire
  • Without Ballast 45.4 tonne at 1.57 m (50 ton at 62 in)

Electrical Controls

  • Option 1 Cat 2000-2400 amp (Two [2] 1200 amp IGBT panels, one per tram motor), 110V DC, IGBT, variable-stepless speed control.
  • Option 2 RTD monitoring of each tram motor & pump motor and the Cat 2000-2400 amp, 110V DC, IGBT, variable-stepless speed control.

Tire/Wheel Option

  • Options 1 54×26 SETCO Solid Tires
  • Options 2 48×25 SETCO Solid Tires
  • Options 3 54×26 SETCO Solid Tires with Heavy Side Wall Plate Protection

Machine Battery

  • Components 1 Battery Tray – dual tray battery assembly
  • Components 2 Coated Tray
  • Components 3 Battery Filling System
  • Components 4 Battery with Plastisol
  • Components 5 Battery Receptacle Kit
  • Components 6 Optional 64SS125-33; 2000 amp hour battery

Battery Charger Options

  • Options 1 Single Output for One Battery
  • Options 2 Dual Output for Two Batteries

Speed

  • Tram Speed (calculated based on 4% rolling resistance) – Level and Empty on 0% Grade 5.1 km/ h
  • Tram Speed (calculated based on 4% rolling resistance) – Level and Loaded on 0% Grade 3.8 km/h

Hydraulic Installation (Standard)

  • Components JIC fittings with 345 bar (5,000 psi) hosing; MSHA 2G flame resistant approved.

Circuit Breaker Options

  • Options 1 Magnetic, UVR Trip – controller enclosure equipped with UVR trip circuit breaker rated mine duty 800 amp frame, 600 volt.
  • Options 2 Optional Cab mounted breaker reset using a single high capacity, swivel end style push/pull cable.
  • Options 3 Standard Cab mounted hydraulic breaker reset with single push breaker trip function.

Standard Load Lift

  • Battery Change System 1 Hydraulically operated, bell crank, forklift battery charger to pick up battery from grade.
  • Battery Change System 2 The battery/battery tray assembly can be further raised to increase the rear approach clearance up to 508 mm (20 in).
  • Center Section 1 Entire center section area manufactured with T1 steel.
  • Center Section 2 Center section is designed with hardened 114.3 mm (4.5 in) diameter pivot pins and spherical bearings.
  • Components 1 Tilting cylinders for tilt lifting of a universal load lift frame
  • Components 2 Heavy duty, pin on, forged alloy steel forks (152 mm × 356 mm × 2134 mm [6 in × 14 in × 84 in]) are standard.
  • Components 3 A combination bell crank arm and bell crank lifting cylinder for vertical lifting
  • Oscillation Section An 813 mm (32 in) diameter bearing with 44.5 mm (13⁄4 in) diameter rolling elements provides 20 degrees of oscillation.
  • Tri-Section Frame 1 The design produces a maximum of stability while maneuvering with a heavy load.
  • Tri-Section Frame 2 The tri-section frame design featuring multiple plate, modular construction for maximum strength and structural integrity
  • Tri-Section Frame 3 All high stressed areas are manufactured with T1 steel.

Machine Accessories (Optional)

  • Type Pressure Switch Kit, Intrinsically Safe – electric/hydraulic system to shutdown the tram motors
  • Type 1 Shield Deflector/cage protector consisting of a frame mounted supported structure.
  • Type 10 Mine Duty, laminated frame, direct current motor rated at 16.4 kW (22 hp) for one hour, 110V DC
  • Type 11 Battery Tray (One Required for Each Battery Assembly)
  • Type 12 Park Brake/Tram Inhibit installation kit
  • Type 13 Tilt Cylinder protection kit consisting of two, hinged, heavy duty steel plates protecting the Tilt Cylinder Rods.
  • Type 14 Cable Guide Assembly.
  • Type 15 Cat 2000 Hand Held Calibrator, LED – used to adjust and troubleshoot the Cat 2000 electrical controller
  • Type 16 Power Disconnect Switch (required in PA).
  • Type 2 In line Flow meter monitoring of the tandem hydraulic pump outputs.
  • Type 3 Ultra heavy duty fork mounted bucket with ejector with quick attach pins.
  • Type 4 Reflector Installation – additional reflectors mounted in strategic locations on the machine.
  • Type 5 Shroeder Testmate with JIC fittings.
  • Type 6 Tram and Pump motors with RTD monitoring.
  • Type 7 Optional Fork Plates or customer specified designs.
  • Type 8 Tow Hook Installation – two tow hooks mounted on the front of machine rated at 10.8 tonne (12 ton) each.

Cab Option

  • Type 1 Manual Adjustable Cab Assembly
  • Type 2 Hydraulically Adjustable Cab Assembly

Lift Attachments

  • Fork Assembly 1 Designed to lift and carry 45.4 tonne (50 ton) at 1575 mm (62 in) from the load lift plate mounted to the machine.
  • Fork Assembly 2 2134 mm (84 ft) Overall Length – set of 2134 mm (84 ft) overall length up-set forged forks
  • Quick Attach Lift Plate 1 Designed to lift and carry 45.4 tonne (50 ton) at 1575 mm (62 in) from the face of the load lift frame.
  • Quick Attach Lift Plate 2 The plate mounts directly to the 2134 mm (84 in) forks through two parallel pockets.
  • Quick Attach Lift Plate 3 2134 mm (84 in) (Fork Assembly Required)

You can help other customers

Have you used this car?

Write A Review

Caterpillar SH650 Roof Support Carriers Pictures

Select Equipment Dealers by Brand and City